Mini ST-LINK/V2 ST-LINK In-circuit Debugger Programmer Emulator Downloader for STM8 and STM32 Low Cost Solution USB Interface Компьютеры - купить

Купить Mini ST-LINK/V2 ST-LINK In-circuit Debugger Programmer Emulator Downloader for STM8 and STM32 Low Cost Solution USB Interface | Компьютеры

Mini ST-LINK/V2 ST-LINK In-circuit Debugger Programmer Emulator Downloader for STM8 and STM32 Low Cost Solution USB Interface

Mini ST-LINK/V2, in-circuit debugger/programmer for STM8 and STM32

Description

Mini ST-LINK/V2 on a small single board, an extreme low cost solution for in-circuit debugger/programmer for STM8 and STM32.

Features Onboard 500mA self-recovery fuse to avoid harming by short circuit Dual voltage output (3.3V/5V), easy for debugging/programming Standard USB interface for direct connection to PC Debugging/Programing performance Debugging : run at full-speed, single-stepped, breakpoints, viewing variables and registers, etc. Programming : supports FLASH ROM, EEPROM, AFR, etc. USB2.0 combined with SWIM/SWD interfaces : quick response for debugging & fast speed for programming Upgradable firmware The firmware is upgradable to support more devices in the future Automatically upgraded Supported software ST-LINK Utility v2.0 (or higher ver.) STVD Version 4.2.1 (or higher ver.) STVP Version 3.2.3 (or higher ver.) IAR EWARM Revision v6.20 (or higher ver.) IAR EWSTM8 Revision v1.30 (or higher ver.) KEIL RVMDK Revision v4.21 (or higher ver.) ATOLLIC TASKING Supported devices All the STM8 devices with SWIM interface All the STM32 devices with SWD interface Photos ST-LINK/V2 (mini) Vs ST-LINK/V2 Vs ST-LINK Compare ST-LINK/V2 (mini) ST-LINK/V2 ST-LINK Remarks

SWD voltage range	1.65V - 3.6V	1.65V - 3.6V	3V - 3.6V	ST-LINK/V2 and ST-LINK/V2 (mini) support STM32 low voltage devices
SWIM voltage range	1.65V - 5.5V	1.65V - 5.5V	1.65V - 5.5V
Supports SWV	NO	YES	NO	For the moment, only STM32 supports SWV while STM8 doesn't
Debug interfaces	2	2	1	ST-LINK/V2 and ST-LINK/V2 (mini) support STM8/STM32 with separated interfaces
LED indicator	Dual color LED	Dual color LED	Red LED	Dual color LED allows indicating more status
Fuse	YES	NO	NO	Fuse for avoid harming by short circuit

Connecting with PC

While connecting the ST-LINK/V2 (mini) to the computer through USB interface, the USB driver is required and should be installed correctly first.

Click on the link to download : ST-LINK/V2 USB driver for Windows 7, Vista and XP

Connection with STM8/STM32 Applications

The ST-LINK/V2 (mini) should be connected to the STM8 application via the SWIM interface.

Debugger Pin Target Board Pin Description

VCC	MCU VCC	STM8 VCC
SWIM	MCU SWIM	STM8 SWIM PIN
GND	GND	STM8 GND
RST	MCU RESET	STM8 RESET PIN

The ST-LINK/V2 (mini) should be connected to the STM32 application via the SWD interface.

Debugger Pin Target Board Pin Description

VCC	MCU VCC	STM32 VCC
SWDIO	MCU SWDIO	STM32 SWD SWDIO
GND	GND	STM32 GND
SWCLK	MCU SWCLK	STM32 SWD SWCLK

Please note that the VCC and GND should be connected correctly to avoid any harm to the ST-LINK/V2 (mini).

Package Contains ST-LINK/V2 (mini) × 1 4-pin custom connector cable × 1 USB type A plug to receptacle cable × 1