Holybro Kakute F7 Flight Controller & Atlalt HV V2 40CH VTX 65A BL_32 Tekko32 F3 Metal 4in1 ESC Combo for RC Drone Игрушки и хобби - купить

Купить Holybro Kakute F7 Flight Controller & Atlalt HV V2 40CH VTX 65A BL_32 Tekko32 F3 Metal 4in1 ESC Combo for RC Drone | Игрушки и хобби

Holybro Kakute F7 Flight Controller & Atlalt HV V2 40CH VTX & 65A BL_32 Tekko32 F3 Metal 4in1 ESC Combo

Specification:
Brand Name: Holybro
Item Name: F7 FC & 65A 4in1 ESC & 5.8G 40CH VTX Stack Combo
Stack Height: 26mm

Kakute F7 Flight Controller ( Manual )

Item name: Kakute F7 MCU: STM32F745 32-bit processor IMU: MPU6000 (SPI) Barometer: BMP280 USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART) 6 hardware UARTS (UART1,2,3,4,6,7) All UARTS support hardware inversion. SBUS, SmartPort, and other inverted protocols work on any UART without “uninvert hack”. Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported. TF card for Blackbox logging Dimensions: 35x41x7mm (includes foam-mounted gyro board in height) Mounting Holes: Standard 30.5mm square to center of holes Weight: 9g
Atlalt HV V2 40CH VTX ( Manual)
Item Name: 5.8G 40CH 25/200/500/800mW FPV Transmitter Model: Atlatl HV V2 Transmitting Output Power: 25mW/ 200mW/ 500mW/ 800mW Switchable Audio: 6 MHz + 6.5 MHz Mono Antenna Connector: MMCX Input Voltage: 7-28V (2-6S Lipo) Dimension: 35(L)x 25(W)x 7(H)mm Mounting Hole: 30.5x30.5mm Weight: 9.3g
Tekko32 F3 Metal 4in1 ESC
Model: Tekko32F3 Metal Item Name: 65A BL_32 32Bit DShot1200 4 in 1 ESC Con. Current: 65A Peak Current: 80A Input Voltage: 4-6S Lipo Support Ext. cap needed for 6s (470uf 35v for 6s usage) - F3(M4 Core) MCU, Runs BLHELI32 firmware, the MCU works at 108Mhz Size: 42x42mm Mounting Hole: 30.5x30.5mm Weight: 12g Notice: 1. The air flow is very import if you want to run this 4in1 in high current. 2. The input cable(from lipo to 4in1), should be good soldered, and at least 12AWG 3. Please use non-metallic isolation standoffs (marked in red in the diagram above) for the mounting holes on the ESC. Because mounting holes and motor pad are connected. Features: - The 4in1 has onboard analog current sensor, and TLM function(then no current reading over TLM) - Using metal case mosfet for better Heat dissipation - BLheli_32 firmware, support Oneshot, Multishot, Dshot150, DShot300, DShot600 and DShot1200

Package Included:
1x Kakute F7 Flight Controller
1x Atlalt HV V2 5.8G FPV Transmitter

1x 80mm SMA--MMCX Cable 1x 150mm 4pin JST GH wire
1x Tekko32 F3 Metal 4in1 ESC 1x 470uF 35V Electrolytic Capacitor 1x 8pin to 8pin 1mm pitch 65mm Cable 1x 8pin to 8pin 1mm pitch 25mm Cable